Matrix-orbital GLT240128 Legacy Manual de usuario Pagina 25
- Pagina / 70
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Syntax
Hexadecimal 0xFE 0x33 [adr]
Decimal 254 51 [adr]
ASCII 254 “3” [adr]
Parameters
Parameter Length Description
adr 1 The new I
2
C write address (0x00 -
0xFF).
Description This command sets the I
2
C write address of the module between 0x00
and 0xFF. The I
2
C write address must be an even number and the read
address is automatically set to one higher. For example if the I
2
C write
address is set to 0x50, then the read address is 0x51.
NOTE The change in address is immediate.
Remembered Always
Default 0x50
4.5 Changing the Baud Rate
Syntax
Hexadecimal 0xFE 0x39 [speed]
Decimal 254 57 [speed]
ASCII 254 “9” [speed]
Parameters
Parameter Length Description
speed 1 Hex value corresponding to a baud
rate.
Description This command sets the RS-232 port to the specified [speed]. The change
takes place immediately. [speed] is a single byte specifying the desired
port speed. Valid speeds are shown in the table below. The display
module can be manually reset to 19,200 baud in the event of an error
during transmission, including transmitting a value not listed below, by
setting the manual override jumper during power up. However, it should
be noted that this command will be ignored until the manual override
jumper is removed again.
Hex Value Baud Rate
0xCF 9600
0x8A 14400
0x67 19200
0x44 28800
0x33 38400
0x22 57600
0x19 76800
0x10 115200
Remembered Always
Default 19,200 bps
Matrix Orbital GLT240128 20
- GLT240128 1
- Technical Manual 1
- Revision: 1.2 1
- Contents 2
- 1 Getting Started 6
- 1.2 Accessories 7
- 1.3 Features 8
- 1.4 Connecting to a PC 9
- 1.5 Installing the Software 10
- 2 Hardware Information 11
- 2.1 Communication Connectors 13
- 2.4 Power Through DB-9 Jumper 16
- 2.6 Protocol Select Jumpers 17
- 2.7 Filesystem Lock Jumper 18
- 2.8 Manual Override 19
- 3 Troubleshooting 20
- 4 Communications 21
- C Transaction Example 22
- 4.2 Turn Flow Control On 23
- 4.3 Turn Flow Control Off 24
- 4.4 Changing the I 24
- C Slave Address 24
- 4.5 Changing the Baud Rate 25
- 5.1 Introduction 27
- 5.2 Uploading a Font File 29
- 5.3 Setting the Current Font 29
- 5.4 Font Metrics 30
- 5.5 Set Box Space Mode 31
- 6.1 Introduction 31
- 6.2 Move Cursor Home 31
- 6.5 Auto Scroll On 32
- 7 Bitmaps 33
- 8 Bar Graphs and Drawing 35
- 8.3 Draw Pixel 36
- 8.4 Drawing a Line 36
- 8.5 Continue a Line 37
- 8.6 Draw a Rectangle 37
- 8.7 Drawing a Solid Rectangle 37
- 8.8 Initializing a Bar Graph 38
- 8.9 Drawing a Bar Graph 39
- 8.11 Shifting a Strip Chart 40
- 9 Touchpad 41
- 9.2 Set Touch Region 42
- 9.3 Delete Touch Region 42
- 9.4 Delete All Touch Regions 42
- 9.5 Set Touch Mode 43
- 9.6 Set Region Reporting Mode 43
- 9.7 Set Dragging Threshold 44
- 9.8 Set Pressure Threshold 44
- 9.9 Run Touchpad Calibration 44
- 10 Display Functions 45
- 10.4 Display Off 46
- 10.5 Set Brightness 46
- 10.6 Set and Save Brightness 46
- 10.7 Set Contrast 47
- 10.8 Set and Save Contrast 47
- 11 Filesystem 48
- 11.2 Wipe Filesystem 50
- 11.3 Deleting a File 51
- 11.4 Get Filesystem Space 51
- 11.5 Get Filesystem Directory 53
- 11.6 Filesystem Upload 53
- 11.7 Downloading a File 53
- 12 Data Security 54
- 12.2 Set Remember 55
- 12.3 Data Lock 55
- 12.4 Set and Save Data Lock 57
- 12.5 Dump the Filesystem 57
- 12.6 Write Customer Data 57
- 12.7 Read Customer Data 57
- 13 Miscellaneous 58
- 14 Command Summary 60
- 14.4 Bitmaps 61
- 14.5 Bar Graphs and Drawing 61
- 14.6 Touchpad 62
- 14.7 Display Functions 62
- 14.8 Filesystem 63
- 14.9 Data Security 63
- 14.10 Miscellaneous 64
- 14.11 Command By Number 64
- 15 Appendix 66
- 15.3 Physical Layout 67
- Figure 24: Physical Diagram 68
- Matrix Orbital GLT240128 63 68
- 15.4 Ordering Information 69
- 15.5 Definitions 69
- 15.7 Revision History 70
Relacionado con productos y manuales para Hardware Matrix-orbital GLT240128 Legacy
Hardware Matrix-orbital GLC24064 Manual de usuario
(44 paginas)
(44 paginas)
Hardware Matrix-orbital GLC24064 Manual de usuario
(63 paginas)
(63 paginas)
Hardware Matrix-orbital LK162-12 Manual de usuario
(41 paginas)
(41 paginas)
Hardware Matrix-orbital LK162A-4T Manual de usuario
(36 paginas)
(36 paginas)
Hardware Matrix-orbital LK162B-7T Manual de usuario
(37 paginas)
(37 paginas)
Hardware Matrix-orbital LK202-25 Manual de usuario
(42 paginas)
(42 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.117 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales